A pipe that splits inside a wall or ceiling turns into a flood in minutes, not hours. Shut the main, then call Water Heater Repairer and a live dispatcher will route you to an independent, licensed and insured plumber near you, plus a water damage contractor if the mess calls for one.
A burst pipe is two jobs at once: stopping the leak and dealing with the water it already dumped. We coordinate both so you are not juggling separate calls while the ceiling sags.
Repairs to supply lines fall under plumbing code, which is why we route only to licensed, insured independent plumbers. Ask to see the license on arrival and check it with your state board.
We triage by severity, so active spray and sagging ceilings move to the front of the line. Arrival is often quick, depending on your location and how many freeze calls are stacked up that night.
The plumber explains what has to open up and writes a flat-rate price before cutting drywall. No surprise line items once the wall is open.
Many contractors in the network carry acoustic leak detectors and thermal imaging cameras. That means smaller access holes and less guessing about where the split actually is.
Split copper, popped PEX fittings, brittle CPVC, and leaks under the slab are all daily calls here. Describe the pipe and where it is, and we connect you with a plumber who handles that exact material all the time.
When water has already soaked drywall, insulation, or subfloor, fixing the pipe is only half the job. We can route a water damage contractor who brings moisture meters, air movers, and dehumidifiers so the framing dries before anything gets closed up. Closing a wet wall is how small leaks turn into mold calls months later.
Pipe material, location, and the reason it broke decide which repair makes sense.
Pipes running through outside walls, vented crawlspaces, and attics are the first to freeze. Ice expands, pressure builds between the blockage and a closed faucet, and the pipe splits lengthwise, often hours later when it thaws.
Type M copper has a thinner wall than Type L, so it tends to split and pinhole sooner. The fix is cutting back to clean pipe and joining it with a sweated or press fitting.
PEX itself flexes, yet the crimp rings and expansion fittings are where freeze damage shows up. CPVC turns brittle with age and heat, and old fittings crack if you so much as bump them.
A warm patch on tile or a water meter still moving with everything off usually means the leak is under the slab. Acoustic detection and thermal imaging pin it down, then you weigh a spot repair against a reroute through walls or attic.
Galvanized steel rusts from the inside, narrowing flow until a threaded joint finally lets go. Fixing one joint on a corroded system tends to stress the next weakest point.
Braided supply hoses on toilets, faucets, and washers can rupture at full line pressure with no warning. A relief valve on the water heater that drips or dumps water needs a look too.
Four steps, and you talk to a person at every one of them.
We walk you through finding the main shutoff and killing power to any wet circuits. Then we ask about the pipe material, the location, and whether any ceiling is sagging.
We route the job to a nearby licensed plumber who carries stock for copper, PEX, and CPVC repairs. If water spread past the leak area, a water damage contractor can be scheduled right behind them.
The pro locates the split, looks over the rest of the line, and notes any pinholes or brittle fittings nearby. You get a written flat-rate quote before any wall gets opened.
The permanent repair goes in, the line is pressure tested, and the plumber watches the joint under full pressure before closing anything up. Ask whether their work comes with a written warranty and get it on paper.
A push-to-connect coupling can stop a spraying line in minutes, which makes it a solid emergency patch. Most plumbers treat them as temporary inside a closed wall, and come back to sweat or press a permanent joint once things dry out.
Close the main valve, then call and we will route a local licensed plumber to you.
A pipe in the outside wall of our laundry room froze and split during the first cold snap. I found the main because the dispatcher stayed on the phone with me, and the plumber had the split copper cut out and replaced within a couple hours. He also showed me the Type M pipe and explained why it went first.
Our water bill doubled and the hallway tile felt warm. The plumber used a listening device and a thermal camera and found the slab leak in about twenty minutes. We got two written prices, spot repair or reroute, and he explained both without pushing.
Water came through the dining room ceiling from an upstairs bathroom supply line. One call got me a plumber for the line and a separate drying contractor for the ceiling and carpet. Having both lined up from one call saved me a long night of searching.
I manage a small rental, and a tenant called about a CPVC elbow that cracked under the kitchen sink. The plumber replaced it, then showed me two more fittings that crumbled when he touched them. I got a written quote to replace the whole run and time to think it over.
Close the main shutoff right away and kill power to wet areas at the panel. Drain the system by opening a low faucet, pull belongings out of the path, and call for a plumber.
Turn on the connected faucet and apply gentle heat with a hair dryer or a space heater nearby. Never use a torch or open flame, since it can scorch framing or flash steam inside the pipe.
They are code-approved in many places, yet a lot of plumbers prefer them only where they stay accessible. Ask the plumber whether a sweated or press fitting makes more sense before the drywall goes back.
Acoustic leak detectors pick up the hiss of escaping water, and thermal imaging shows cool or warm patches where it spreads. Together they usually narrow the access hole to a small, patchable opening.
A single leak on newer pipe often makes sense to spot repair through the floor. Repeated leaks or aging copper tend to point toward a reroute so you are not breaking concrete again next year.
Let faucets on outside walls drip on hard freeze nights and open the sink cabinets so warm air reaches the pipes. Insulate exposed runs and add heat tape where pipes pass through cold crawlspaces, starting with the spots the plumber flags.
We route calls to independent plumbers working all over Portland, from older neighborhoods with galvanized lines to newer builds plumbed in PEX. Surrounding suburbs are part of the coverage, including zip codes like 37148.
Older homes near the center of town tend to have galvanized mains and thin copper branch lines, which is where pinhole leaks and corroded threads show up. Newer subdivisions are mostly PEX or CPVC, so blown crimp fittings and cracked elbows top the list there. Wherever you are, tell the dispatcher the age of the house and we match the plumber to the pipe.
Frozen crawlspace pipes, attic runs, and slab leaks across older and newer houses.
Leaks that cross into a neighbor's unit, where fast shutoff and documentation both matter.
The same contractor network reaches the suburbs around Portland.
